PART NUMBER: 108058
Alternator Connector Splice TTASame as 108070, but fits 1989 TTA using TWO brown wires...
$9.13
PART NUMBER: 108095
Alternator Connectors Mating Pair w/ wiresThis pair of connectors will not only replace a defective alternator plug but provides a MATE for the alternator plug. This allows insertion of any accessory to the regulator side of the alternator. These plugs are used on our "Plug-And-Play" Volt Booster fo..
$24.43
PART NUMBER: 102031
Battery & Extension Cable 1986/1987Factory positive cable problems, and fuselink problems with the OEM setup prompted us to design this relocation kit. This custom-designed kit provides a convenient junction for the positive battery cable AND relocates the fuse links from the starter stud to the..
$119.99
PART NUMBER: 108076
Battery Cable Fuselink Connector - TTAThis connector is found on the positive battery cable, 89 TTA, and containstwo fuselinks. Feeds the ECM MEM control and fuel pump relay. Replaces the OEMsetup frequently damaged by battery acid. Mates with our 108077,which is the engine harness side...
$9.13
PART NUMBER: 102026
Battery Negative Cable 84/87Eliminate electrical "gremlins" with a new cable. Our negative cable is manufactured to OEM specifications, using the new "slip-over" terminal cover design. Secondary ground pigtail wire included...
$34.63
PART NUMBER: 102025
Battery Positive Cable TTAThe factory positive cable is obsolete. We manufacture ours to factory specifications, except we add extra length to the starter cable extension, so it wont contact the down-pipe (particularly the aftermarket large-diameter down-pipes), eliminating the most common cause o..
$94.81
PART NUMBER: 102043
Battery Positive Extender Heavy DutyThis specially built kit is designed to: 1) to re-locate the fuse links from the starter location to a location in the engine bay for easy access, 2) to allow for easy attachment of accessories to the battery positive terminal, 3) to add extra fuse links so that e..
$139.99
PART NUMBER: 103032
Breather - LS1 & 3800
This is a chrome top Breather Assembly with heavy duty
billet Aluminum base. Bayonet type lock attaches securely
to the valve cover. Used on the LS1 GM engine and Supercharged 3800
Series II engine. Bayonet twist-lock mounts securely and seals with
an O rin..
$46.00
PART NUMBER: 108028
C-100 Bulkhead Splice 1984 / 1987 Turbo RegalThis critical feeder connector is located on the drivers side, directly below the power brake system. Part of the main wiring harness, it connects thru the firewall and contains all feeders. Body wiring connector attaches to the open half. Since it is uns..
$64.77
PART NUMBER: 108049
C437 Mating Connector with Terminals - 84/87For the do-it-yourselfers, this connector assembly is the actual harness connector found on the dash harness which mates with the two connectors on the engine harness, near the ECM. NOTE: Proper crimp tool required for proper installation...
$26.47
PART NUMBER: 108050
C437 Mating Pair - 84/87Located under throttle linkage, on top of lower intake. Attaches to hi temp switch, green wire with yellow stripe, controls hi speed relay and delay relay. ..
$31.57
PART NUMBER: 109089
CAM HARNESS 40inchesThis harness allows the cam sensor used on the front of a LS2 motor to be plugged into the LS1 cam sensor connector located at the back of the intake manifold. This harness is perfect for LS2 motor conversions. Compatible with the PCM harness in LS1 Corvette and F-Body cars.- Ful..
$26.47
PART NUMBER: 107112
Cam Sensor Cap Only 1984 / 1989
New design provides a simple and accurate procedure to set the required 25 degree ATDC cam sensor signal. Has built-in LED which indicates an exact setting point. You simply rotate your engine to Top Dead Center and this cap does the rest. No need to index your crank..
$75.95
PART NUMBER: 108021
Cam Sensor Splice 1984 / 1989This connector is part of the actual CAM sensor, on the sensor end, NOT THE HARNESS END...
$9.13
PART NUMBER: 108020
Cam Sensor Splice Engine Side - 1984 / 1989Buick Turbo Regal and Pontiac Turbo TransAm..
$9.13
PART NUMBER: 108063
Canister Purge Splice -84/89Located at charcoal cannister, front driver's side near radiator core support. Red connector, 2 cavity...
$9.13
PART NUMBER: 103100
Casper's Power Pack for 1986/1987 Turbo RegalSpecially designed kit that provides wiring upgrades for every potential "weak spot" on your turbo Regal. Designed for the most popular 1986 and 1987 model years. Complete package for stock to modified GN's and turbo Regals. Special price saves you 10% ov..
$394.69
PART NUMBER: 102086
CCCI AdapterUse this "Plug-and-Play" system to adapt the newer 87-style CCCI module to the early 84/85 turbo engine wiring harness. Use our 102085 CCCI Mounting Plate, to facilitate complete installation on your 84-85 turbo engine.NOTE: Coil pack & ignition modules are not available through..
$105.00
PART NUMBER: 108017
CCCI Connector With Terminals and SealsFor the do-it-yourselfers, this connector assembly is the actual harness connector used on the CCCI module, 1984-1989. Black connector comes complete with 14 Pull-to-Seat 16 gage terminals. NOTE: Proper crimp tool required for proper installation...
$27.49